Home-Made Squirrel Detector

Since we published C.Bear’s story “The Elusive Mr. S”, we’ve already received a request from a fan who wanted to know, “Where can I get one of those Squirrel Detectors?” Actually, it’s so simple that we make our own. Now, you can do the same. Just follow these simple instructions. Before you know it, you’ll be in the squirrel detection business as well.

PARTS LIST

1 cedar shingle
1 helical copper wire coil
1 dipole receiver antenna, approx. 1-1/2 in long
1 used watch or motherboard battery
1 5/16 or 3/8 steel nut (metric OK)
1 tube Duco or Ambroid household cement

Figure 1 (click picture for larger image)

click picture for larger image

CONSTRUCTION

Locate a cedar shingle in good condition, not too weathered. First, split it along the grain so you have a piece approximately 3 inches wide. Now trim it to a more compact length, say, about 5 inches long. Plan your cut so that the 5″ section includes the feathered thin edge of the shingle. The feathering enhances detection of birds, while not impairing squirrel detection in the slightest.

Exact dimensions are not critical in any part of the construction.

The detection parts consist of a (1) power source, (2) receiving and (3) transmitting antenna, and (4) the actual detector.

1) Any old battery will do, as this is a very low-power device. Flat batteries are easier to glue to the shingle.

2) You can wind your own receiving coil with a stiff copper or baling wire. Wrap several turns around a form (a magic marker is about the right diameter). Carefully bend the last 1/4 inch upright to impress your friends.

3) Fashion your dipole (transmitting) wire from matching wire stock.

4) Locate a good 5/16″ or 3/8″ nut. We favor sprocket nuts from old Schwinn bicycles, but anything of about the right size will do. Metric is excellent, and will enhance old-world bird detection as a bonus. Chrome-plated nuts are hard to find, but they do show off your detector to the best advantage.

Now, glue the parts into place. Referring to Figure 1, along a left to right center line, glue your receiving antenna, transmitting antenna, battery, and detection nut. Allow to dry overnight.

No wiring or soldering is required. The parts are already interactive. Although no particular voltage is required, locating a battery holder allows you to more easily replace your battery with a fresh one, if desired.

Finishing touches: Perfectionists may want to spray varnish the assembly with several coats of marine spar varnish. Cedar is excessively absorbent, so be warned you will need several coats for a uniform gloss. On the other hand, natural cedar ages gracefully to a fine grayish patina, so we side with purists who deem the detector “finished” once the parts are glued into place and dried.

TESTING AND USAGE

Now comes the best part. You are ready to test your genuine, original new Squirrel Detector (though truthfully there is so little that can go wrong).

Take your detector to a park, garden, back yard or wooded area that squirrels are known to frequent. You can place your detector on your car dashboard, or aim it in your hands in a sweeping motion around the grounds. Either method works equally well. When you see a squirrel, go “Beep! Beep” to train your detector. Thereafter, when you see a squirrel, go “Beep! Beep!” to keep your detector in prime condition.

Congratulations! Your detector is already trained and working!

EXTRA FEATURES

Your squirrel detector is also capable of detecting some bird species (assuming you used the end of the shingle with the feathered edge):

When you see a duck, go “Quack-Quack!”

When you see a goose, go “Honk! Honk!”

When your friends see your detector in operation, not only will you be the talk of the neighborhood, you alone will hold the secret of how to construct a genuine Squirrel Detector!

NOTES

1. Results may vary. Do not be discouraged if you don’t start detecting squirrels right away. Try a different park. Since you are responsible for fashioning your own detector, we can offer no warranty, expressed or implied.

2. Not intended for use in the Mojave, Gobi or the various continental ice shelves.

3. Your Squirrel Detector already has the built-in Language plug-in. On hearing the special cue words “Beep! Beep”, “Quack-Quack!” or “Honk! Honk”, savvy bystanders in any country will have no trouble understanding what’s going on here.

4. Never point your device at large, menacing wild animals.

Copyright Alex Forbes May 15, 2005

1,415 total views, 2 views today